VMTV
(6901-100175 <01>)
IMPORTaNT SaFETY INSTRuCTIONS - SaVE THESE INSTRuCTIONS
Thank you for choosing a Sanus Systems VMTV monitor mount.The VMTV monitor mount is designed to support
monitors 13 to 27 inches (33 to 68 cm); maximum weight capacity is 45 kg (100 lbs.). The VMTV monitor mounts are
adjustable, allowing up to 110˚ of swivel, up to 180˚ of roll, and three tilt settings 0˚, -5˚, and -10˚.
CauTION
Do not use this product for any purpose not explicitly specified by Sanus Systems. Improper assembly may cause
property damage or personal injury. If you do not understand these directions, or have doubts about the safety
of the assembly, contact Customer Service or call a qualified contractor. Sanus Systems is not responsible for
damage or injury caused by incorrect assembly or use.
CauTION
This product is designed for use in wood stud walls only! The wall must be capable of supporting up to five times
the weight of the monitor and mount combined. If you have any doubts about the ability of the wall to support
the monitor, contact Customer Service, or a qualified contractor.
WaRNING
This product contains small items that could be a choking hazard if swallowed. Keep these items away
from young children!
Sanus Systems 2221 Hwy 36 West, Saint Paul, MN 55113 USA
Customer Service: 1-800-359-5520 • 651-484-7988
©2008 Milestone AV Technologies
1
7/32 in.
63.5 mm
(2.5 in.)
[01]
[09]
CauTION
Avoid potential injuries or property damage! Do not
overtighten the lag bolts [09]. Tighten the bolts only
until they are pulled firmly against the wall plate [01].
[01]
6901-100175 <01>
2
[10]
NOTE
Do not overtighten the pivot nut [12]. The
arm [03] must be free to move.
[03]
[12]
[02]
[08]
[06]
6901-100175 <01>
3
[11]
0° Tilt
-5° Tilt
-10° Tilt
[11]
CauTION
Avoid potential injuries or property damage! Do
not use the -10° Tilt position for monitors larger
than 23 in. (68 cm) or weighing more than 27 kg
(60 lbs.).
CauTION
Avoid potential injuries or property damage!
Be sure the square shoulder of the bolt [11]
seats completely into the square hole before
tightening the bolt.
[15]
[14]
[13]
6901-100175 <01>
4
[06]
5
[a]
NOTE
Loosen the eight fasteners shown. Adjust the
platter so that the slots [A] are slightly wider than
the width of the monitor. Retighten the fasteners.
[a]
6901-100175 <01>
6
[04]
HEAVY! You will need assistance
with this step. Have an assistant hold
the monitor in place on the platter
while you secure the strap [04].
1
2
3
CauTION
Avoid potential injuries or property damage!
Never leave the monitor on the wall mount
unless the strap [04] is securely fastened.
6901-100175 <01>
Milestone AV Technologies, Inc. and its affiliated corporations and subsidiaries (collectively,“Milestone”), intend to make this manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details, conditions, or variations. Nor does it provide for every possible contingency in connection with the installation or use of this
product.The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
6901-100175 <01>
|